Per¶
SCPI Commands
CONFigure:EVDO:SIGNaling<Instance>:RXQuality:PER:TOUT
CONFigure:EVDO:SIGNaling<Instance>:RXQuality:PER:REPetition
- class Per[source]
Per commands group definition. 2 total commands, 0 Sub-groups, 2 group commands
- get_repetition() → RsCmwEvdoSig.enums.Repeat[source]
# SCPI: CONFigure:EVDO:SIGNaling<instance>:RXQuality:PER:REPetition value: enums.Repeat = driver.configure.rxQuality.per.get_repetition()
Specifies the repetition mode of the packet error rate (PER) measurement. The repetition mode specifies whether the measurement is stopped after a single-shot or repeated continuously. Use method RsCmwEvdoSig.Configure.RxQuality.FlPer. mtpsent or method RsCmwEvdoSig.Configure.RxQuality.RlPer.mpSent to determine the number of test packets per single shot.
- return
repetition: SINGleshot | CONTinuous SINGleshot: Single-shot measurement CONTinuous: Continuous measurement
- get_timeout() → float[source]
# SCPI: CONFigure:EVDO:SIGNaling<instance>:RXQuality:PER:TOUT value: float = driver.configure.rxQuality.per.get_timeout()
Defines a timeout for the measurement. The timer is started when the measurement is initiated via a READ or INIT command. It is not started if the measurement is initiated manually ([ON | OFF] key or [RESTART | STOP] key) . When the measurement has completed the first measurement cycle (first single shot) , the statistical depth is reached and the timer is reset. If the first measurement cycle has not been completed when the timer expires, the measurement is stopped. The measurement state changes to RDY. The reliability indicator is set to 1, indicating that a measurement timeout occurred. Still running READ, FETCh or CALCulate commands are completed, returning the available results. At least for some results, there are no values at all or the statistical depth has not been reached. A timeout of 0 s corresponds to an infinite measurement timeout.
- return
timeout: Unit: s
- set_repetition(repetition: RsCmwEvdoSig.enums.Repeat) → None[source]
# SCPI: CONFigure:EVDO:SIGNaling<instance>:RXQuality:PER:REPetition driver.configure.rxQuality.per.set_repetition(repetition = enums.Repeat.CONTinuous)
Specifies the repetition mode of the packet error rate (PER) measurement. The repetition mode specifies whether the measurement is stopped after a single-shot or repeated continuously. Use method RsCmwEvdoSig.Configure.RxQuality.FlPer. mtpsent or method RsCmwEvdoSig.Configure.RxQuality.RlPer.mpSent to determine the number of test packets per single shot.
- param repetition
SINGleshot | CONTinuous SINGleshot: Single-shot measurement CONTinuous: Continuous measurement
- set_timeout(timeout: float) → None[source]
# SCPI: CONFigure:EVDO:SIGNaling<instance>:RXQuality:PER:TOUT driver.configure.rxQuality.per.set_timeout(timeout = 1.0)
Defines a timeout for the measurement. The timer is started when the measurement is initiated via a READ or INIT command. It is not started if the measurement is initiated manually ([ON | OFF] key or [RESTART | STOP] key) . When the measurement has completed the first measurement cycle (first single shot) , the statistical depth is reached and the timer is reset. If the first measurement cycle has not been completed when the timer expires, the measurement is stopped. The measurement state changes to RDY. The reliability indicator is set to 1, indicating that a measurement timeout occurred. Still running READ, FETCh or CALCulate commands are completed, returning the available results. At least for some results, there are no values at all or the statistical depth has not been reached. A timeout of 0 s corresponds to an infinite measurement timeout.
- param timeout
Unit: s